Colliers de réparation pour joints de courbure de tuyaux PE, PVC, UPVC HDPE

Informations de base.

Numéro de modèle.	DN63
Forfait Transport	Boîte en carton
spécification	DN63
Marque déposée	GRANDE MURAILLE
Origine	Chine
Code SH	7307290000

Description du produit

Pinces de réparation UPVC

1. Mémoires :
* Costume pour la réparation d'urgence de tuyaux qui fuient sous pression
* Pression de service : PN10/PN16
2. Caractéristiques :
* Costume pour tuyaux PE, PVC, UPVC, HDPE
* Costume pour tuyau droit, joint de fusion bout à bout, joint de fusion à douille, joint plié, joint en T
* Solution rapide pour fuite de pipeline
* installation et démontage faciles
3. La liste des tailles

S/N	Description		Taille		Pression
			mm	pouce	Mpa
1	Pinces de réparation UPVC	Correction directe	DN50	2''	1.0
2	Pinces de réparation UPVC	Correction directe	DN63	2,5''	1.0
3	Pinces de réparation UPVC	Correction directe	DN75	3''	1.0
4	Pinces de réparation UPVC	Correction directe	DN90	3,5''	1.0
5	Pinces de réparation UPVC	Correction directe	DN110	4,5''	1.0
6	Pinces de réparation UPVC	Correction directe	DN125	5''	1.0
7	Pinces de réparation UPVC	Correction directe	DN140	5,5''	1.0
8	Pinces de réparation UPVC	Correction directe	DN160	6,5''	1.0
9	Pinces de réparation UPVC	Correction directe	DN180	7''	1.0
dix	Pinces de réparation UPVC	Correction directe	DN200	8''	1.0
11	Pinces de réparation UPVC	Correction directe	DN225	9''	1.0
12	Pinces de réparation UPVC	Correction directe	DN250	dix''	1.0
13	Pinces de réparation UPVC	Correction directe	DN280	11''	1.0
14	Pinces de réparation UPVC	Correction directe	DN315	12,5''	1.0
15	Pinces de réparation UPVC	Correction directe	DN355	14''	1.0
16	Pinces de réparation UPVC	Correction directe	DN400	16''	1.0
17	Pinces de réparation UPVC	Correction directe	DN500	20''	1.0
1	Pinces de réparation UPVC	Réparation du tee

a. UPVC repair clamps is only suit for Butt Fusion Joint and Socket Fusion Joint of Plastic Pipe but it's not suit for Electro Fusion Joint of Plastic Pipe. b. The size and pressure rating of UPVC repair clamps should be match up with the size and pressure rating of leaking pipeline. The pressure rating of UPVC repair clamps is 1.0 Mpa ( 10 bar ) and it is prohibited to use UPVC repair clamps if the operation pressure of your pipeline is above 1.0 Mpa (10 bar ) c. You should check the surface of UPVC repair clamps if there is any crack or damage before installation and the UPVC repair clamps with crack or damage is prohibited to use . d. The pressure of pipeline should be reduced before installation of UPVC repair clamps . e. The oxidizing material and mud on the surface of pipeline should be cleaned before installation and then check the breakage of pipeline and the broken pipeline should be cut off and replaced if it's long and you are not recommended to use UPVC repair clamps for the leaking pipeline with the oversize breakage. f. Put the lubricant ( such as soap water, detergent and etc) on the pipeline surface and rubber gasket of repair clamps for the role of lubrication which is needed for position adjustment of repair clamps during installation process . g. uninstall the vent hole plug of repair clamps and then fix the leaking position with two half bodies of repair clamps and fasten with bolts and nuts in diagonal direction . h. wrap the plug with tape and fix into vent hole of repair clamps i. You should not start the pump until air inside the pipeline exhausted by the exhaust device of pipeline and then restore pipeline pressure when air exhausted .